Makita DA6300 7.5 Amp 1/2-Inch Joist and Stud Drill |  | Brand: Makita
Category: Home Improvement
List Price: $546.00
Buy New: $373.95
as of 7/31/2010 19:32 CDT details
You Save: $172.05 (32%)
Seller: Toolfetch
Rating:  reviews
Sales Rank: 99883
Media: Tools & Hardware
Number Of Items: 1
Shipping Weight (lbs): 9.5
Dimensions (in): 18.8 x 8.9 x 7.7
MPN: DA6300
Model: DA6300
UPC: 088381005173
EAN: 0088381005173
ASIN: B00004YOKI
Availability: Usually ships in 3-4 business days
| |
| Features:
| • | All ball and needle bearings for long tool life | | • | 2 speed (300 rpm or 1,200 RPM) for increased drilling versatility | | • | Triple reduction gearing for maximum power | | • | Rocker type reversing switch for easy one handed change of bit rotation | | • | Powerful 7.5 amp motor for continuous production |
|
| Accessories:
| |
| Editorial Reviews:
Product Description
Makita DA6300 1/2" Angle Drill
|
| Customer Reviews:
Powerful, high-quality, drill. Poor case. September 18, 2005
Victor H. Agresti (Gaithersburg, MD United States)
3 out of 3 found this review helpful
Makita DA6300 Heavy Duty [compact] Right-Angle Drill
If you've never used this type of drill, be forewarned: This tool has so much torque, especially at the 300-RPM setting, that you could be hurt if not careful. This isn't a tool for a woman, unless she's a weightlifter. For large holes, say 3" and up, you must absolutely use the side handle. This is because when a large bit becomes stuck while you're drilling, a common scenario, the tool itself starts to rotate - so you need to be holding on with every ounce of strength you have to prevent that - and be quick to release the switch. If you don't, it could lift you right of the ground, twist your arms like pretzels, or mash your fingers, etc. This phenomenon is call kickback. Think safety, and you'll be fine.
The off/on switch is a spring-loaded rocker. For safety reasons, it can't be locked in the "on" position. To turn the bit clockwise, squeeze the rear of rocker-switch. To go counter-clockwise, squeeze the front of the switch. Release the switch, and it instantly moves to the middle/off position - and the bit will stop quickly. To change speeds, pull out a pin on a control near the front handle, and move the slide to the other speed. Both switches are perfect.
The DA6300 comes with a steel case (part no. 181685-2), but it's flimsy, has a lousy handle and latches, and has sharp non-rolled edges. The case has four protruding dimples designed as "feet". However, the case half edges poke out beyond the "feet", so don't set the case's feet on a hardwood floor, counter-top, etc., as it could scratch the surface. The case's steel is only .033" thick. Makita should be embarrassed to put their name on it, which is probably why they don't have a photo of it on their web site. Click "see customer images" above for photos of my case.
The 5 stars are for the drill. The case deserves zero stars.
September 2007 update: When I purchased this tool, I needed a compact heavy-duty right angle drill, such as this one or the Milwaukee Hole Hawg. Neither one had, or even has now, a clutch to prevent tool damage and operator injury during serious kickback. Recently, Ridgid introduced this type of drill, the Model R7130, which has this important safety feature.
After using the DA6300 for a dozen years, my drill bit the dust. I failed to let the drill come to a complete stop before moving the speed selector. (The user guide didn't say the drill had to be stopped to change speeds.) Grinding noises started immediately and the drill chuck stopped moving. Several gears were stripped and the aluminum case cracked. Tool was a total loss. Don't make the same mistake.
Best one out there September 12, 2009
C. swift
I am an Electrical Contractor. Primarily new residential work. Ive been drilling studs, beams, etc.. etc. for years and there is no Rigid, Milwaukee, or any other manufacturer that can build a hole hawg that comes anywhere close to this drill. I use 7/8 ship augers on high speed all day long, and 1-1/2 self feeding bits ( plumbers bit) on high speed as well and can drill out a house twice as fast as any competitor. i do recommend replacing brushes every 25 homes or so, keeping a spare handle and spare chuck key on hand. The Makita chucks only fit makitas, and the handle will break if dropped hard enough on it. However having it made with plastic is a safety feature. Id rather have the handle break than my wrist break! Anyways people, throw those Milwaukee hole shooters and hole hawgs away! boo on those things.
|
|
|
